This is the COMPLETE Operator’s Manual for the Kubota K008-3 Excavator.
This Manual Describes Procedures for Operation, Handling, Lubrication, Maintenance, Checking, and Adjustment. It Will Help The Operator or anyone Realize Peak Performance Through Effective, Economical and Safe Machine Operation and Maintenance.
OPERATOR’S MANUAL CONTAINS:
=========
SAFE OPERATION
DEALER SERVICE
TECHNICAL DATA
DESCRIPTION OF MACHINE PARTS
INSTRUMENT PANEL AND CONTROL ELEMENTS
BEFORE START
HANDLING THE SAFETY DEVICES
Control lever lock
Swing lock pin
DAILY CHECKS
OPERATION OF THE ENGINE
STARTING THE ENGINE
Hourmeter
Checkpoints after Starting the Engine
STARTING THE ENGINE UNDER COLD CONDITIONS
STOPPING THE ENGINE
Engine Stop Lever
STARTING WITH AN AUXILIARY BATTERY
Observe Following Guidelines when Starting with an Auxiliary Battery.
Precautions in case of overheat
EXCAVATOR OPERATION
CONTROL OBSERVATIONS DURING OPERATION
Stop the Engine immediately if:
Alarm Lamps
RUNNING-IN OF THE NEW EXCAVATOR
Do not Work with Full Revolutions or Full Loads during the First 50 Working Hours
Oil Change in the Run-in Stage.
STARTING
Seat Belt and Adjusting the Operator’s Seat
Working Light Switch
CONTROLS FOR ATTACHMENTS
OPERATION OF THE BOOM
OPERATION OF THE ARM
OPERATION OF BUCKET
SWIVEL (UNIT SWING) OPERATION
BOOM SWING OPERATION
BOOM SWING PEDAL
OPERATION OF TRACK WIDTH CHANGE AND DOZER
Operation of the Track Width
Operation of the Dozer Width
Operation of the Dozer
DRIVING
Drive Levers (Right, Left)
TURNS
Pivot Turn
Spin Turn .
UP AND DOWNHILL TRAVELLING
PARKING ON A SLOPE
DRIVE SPEED PEDAL
SERVICE PORT OPERATION
IMPORTANT INFORMATION ON EXCAVATOR OPERATION
OPERATING FOLDABLE ROPS
To Fold the ROPS
To Raise the ROPS to Upright Position
Adjustment of Foldable ROPS
TRANSPORTING THE EXCAVATOR ON A TRUCK
LIFTING OF THE EXCAVATOR
MAINTENANCE
MAINTENANCE INTERVALS
OPENING AND CLOSING OF PARTS
Opening/Closing of the Engine Hood
Keep the Tools and Operator’s Manual in the Toolbox
DAILY CHECKS
Coolant Check
Check Fuel Level
Check Engine Oil Level
Check Hydraulic Oil Level
Lubrication Points
Check Radiator
Cleaning of Engine and Electrical Wiring
Checking the Electrical Circuit
Washing the Whole Machine
Checking Seat Belt and ROPS
REGULAR CHECKS AND MAINTENANCE WORK
EVERY 50 SERVICE HOURS
Draining the Water from the Fuel Tank
Draining of the Fuel Filter
Battery Service
Battery Charging
Greasing of Swing Bearing Teeth
EVERY 200 SERVICE HOURS
Checking the Fan Belt Tension
Checking the Radiator Hoses
Inspection and Cleaning of the Air Filter Element
Air Filter Maintenance
Greasing of the Swing Bearing
Checking Fuel Line and Intake Air Line
EVERY 500 SERVICE HOURS
Engine Oil Change (Change the engine oil every 500 hours, or every 1 year in the case that service hour is less than 500 hours)
Replacing Engine Oil Filter (Replace the engine oil filter every 500 hours, or every 1 year in the case that service hour is less than 500 hours)
Replacing Fuel Filter Element
EVERY 1000 SERVICE HOURS
Hydraulic Oil Change (Including Replacing of the Suction Filter and the Return Filter in the Hydraulic Tank)
Hydraulic Oil Check with Hydraulic Breakers
EVERY 1000 SERVICE HOURS OR ONCE A YEAR
Replacing Air Filter Element
EVERY 1500 SERVICE HOURS
Checking Fuel Injection Nozzle (Injection Pressure)
EVERY 2000 SERVICE HOURS
Changing Front Idler and Track Roller Oil
Checking the Dynamo and Starter Motor
EVERY 3000 SERVICE HOURS
Checking Injection Pump
ANNUAL SERVICING
Electrical Wiring and Fuses
BIENNIAL SERVICING
Replacement of Radiator Hoses
Changing Radiator Coolant
Replacing Fuel Hose
Replacing Intake Air Line
OTHER SERVICING
Cleaning the Track Frame Telescopic Beams
OTHER ADJUSTMENTS AND REPLACEMENTS
PURGING OF THE FUEL SYSTEM
ADJUSTMENT OF CRAWLERS
Special Information when Using Rubber Crawlers
CHANGING THE BUCKET
FUSES
Replacing Fuses
Fuse Capacities and Circuits
Slow Blow Fuse
TROUBLESHOOTING
OPERATION IN COLD WEATHER CONDITIONS
PREPARATION FOR OPERATION IN COLD WEATHER
PROCEDURE AFTER WORK CARRIED OUT
LONG STORAGE
RECOMMENDED OILS
MAIN DIMENSIONS
LIFTING CAPACITY
=========
** Model Specification: Kubota K008-3 Excavator
** Language: English
** Total Pages: 82
** File Format: PDF
** Requirements: Adobe PDF Reader
** Compatible: All Versions of Windows & Mac, Linux OS, Iphone, Ipad, Android etc…
=========
This QUALITY manual is 100 percents COMPLETE and INTACT,
no MISSING/CORRUPT pages/sections to freak you out! It also is Bookmarked and SEARCHABLE to make what you need easy to find. Complete download comes in PDF format which can work under all PC based Windows operating system and Mac also. It saves to your hard-drive and can be burned to CD-ROM. It can be viewed on any computer, as well as zoomed and printed.
Thanks for Visiting!
